Diamond Blemishes

Chip

A small notch or void at the edge of a polished diamond — at a facet junction, the girdle, or the culet — caused by impact. Chips are among the most practically significant blemish types because they create stress concentration points and can affect durability as well as appearance.

Where chips occur and why

Diamond is the hardest natural material but has cleavage planes — directions in the crystal lattice where it can split with relatively modest force if struck at the right angle. Facet junctions and the girdle are the most exposed geometric features of a polished diamond; when struck against a hard surface (another diamond, granite countertop, metal ring), the concentrated force at these thin edges can cause chipping along a cleavage plane.

The most common chip locations:

Chips in pre-owned and estate diamonds

Pre-owned diamonds are at higher chip risk than new stones — accumulated years of wear increase the probability of impact damage. When evaluating a second-hand diamond, inspect the girdle perimeter carefully under 10× magnification, checking especially at any points (for fancy shapes) and at the culet. A chip that has been present for years without propagation is likely stable; a fresh chip (sharp edges, no worn rounding) may be more recent.

On a GIA report for a second-hand stone, a chip will appear in the key to symbols and be plotted on the clarity diagram. If you are having a stone appraised or re-graded after purchase, any chips discovered will be reflected in the clarity grade. See our second-hand diamond buying guide for a full inspection checklist.

Related blemish and clarity terms

Frequently Asked Questions

What is a chip on a diamond?

A chip is a small void or notch at the edge of a diamond — typically at a facet junction (where two polished facets meet), at the girdle, or at the culet. Unlike inclusions (which are internal) or cavities (which are pits within a facet surface), chips are notches at the stone's edges or boundaries. They are caused by impact — the sharp geometry of facet edges concentrates stress, making them vulnerable to chipping when struck against hard surfaces.

How does a chip affect a diamond's clarity grade?

GIA classifies chips as blemishes and plots them on the clarity diagram. A chip at the girdle is often shown as a small angular mark at the girdle line. The impact on the clarity grade depends on size and location: a tiny chip at the girdle may result in SI1 or VS2; a larger chip on the table edge or culet area can pull the grade to SI2 or lower. The key to symbols section of the GIA report will label the feature as "Chip."

Can a chipped diamond be repaired?

Yes — a lapidary can repolish the chipped area to remove it, which slightly reduces carat weight and may change the stone's proportions. The feasibility depends on the chip's size and location. Chips at the girdle are relatively straightforward to polish out; chips on large crown or pavilion facets require more substantial repolishing. Whether repolishing is economically worthwhile depends on stone value and chip severity. For any pre-owned diamond you are considering, have chips evaluated by a jeweller before purchase.

Are chips dangerous in terms of further breakage?

A chip creates a stress point — the notch geometry concentrates any impact force, making further chipping from the same location more likely than on an unchipped stone. This is a particular concern for: (a) chips at pointed extremities of fancy shapes (marquise tips, pear tips, heart cleft), where the geometry is already vulnerable; (b) chips at the girdle in a thin-girdle stone; (c) chips that are associated with a small fracture extending inward. Chips at these locations warrant more serious consideration than equivalent chips on stable facet junctions. See our ring care guide for how to protect chips during wear.

Should I avoid a diamond with a chip?

It depends on size, location, and setting. A tiny girdle chip concealed under a prong — invisible face-up and protected by the setting — may be entirely acceptable, especially if it yields a price concession. A chip on the table facet edge or culet is more significant. A chip at the tip of a marquise or pear raises durability concerns. The right question is: will this chip be concealed by the setting, does it make the stone look damaged face-up, and does the price reflect the clarity grade? Always see the GIA report and confirm eye-clean status with imagery. Compare prices at CaratAtlas (CC BY 4.0).